Booking

 

We've stumbled upon this article on A Step-by-Step Guide to Installing a Bathtub listed below on the internet and figured it made perfect sense to share it with you over here.

Installing a tub isn't precisely brain surgery, however it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably challenging task. If the old tub is easily available, the task can move immediately; if you need to open a wall surface to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will certainly need a helper to leave the old tub as well as embeded in the brand-new one. See to it you have qualified yourself for the task and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed job, it is better to consider employing one prior to you begin. Possibilities are you may require a professional plumber to make tube links.
This short article will help you install a new tub in your bathroom if you have currently gotten a brand-new bathtub as well as don't need to change the setup of your previous supply of water pipelines.
Your devices and product list must comprise the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the limited accessibility that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will certainly originate from the pipelines. Once the supply pipes have been removed, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning throughout this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before moving on to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.

 

 

Suitable New Taps

If the tails of the new taps are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the tap and the other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the mounting hole in the bath/basin making certain that the washing machines are in location in between the faucet and also the sink. Protect the faucet in position with the maker offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap adapters. The previous kind must be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Setting up the Bathtub

Making use of the two wood boards under its feet, put the bathtub in the needed position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The following goal is to ensure that the tub is leveled all round. This can be attained by checking the level as well as readjusting the feet on the bathtub up until the level reads level.
To install taps, fit all-time low of the furthest flexible tap adapter to the appropriate supply pipeline by making a compression join; then do the very same for the other tap.
Turn on the supply of water and examine all joints and also brand-new pipework for leakages and also tighten them if required. Fill the bathtub and additionally inspect the overflow outlet as well as the regular outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the maker's instruction manual. Tiling and securing around the tub ought to wait until the bath tub has actually been used at least when as this will resolve it right into its final placement.

 

 

Getting ready for the Installation

To start with, the supporting structure supplied with the bathroom must be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap connectors to the bottom of both faucets using 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last placement.

 

 

Tiling Around the Bathtub

In the area where the bath meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bathroom and the tiling, causing complications with moisture and feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, and can securing voids up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bathtub with water prior to sealing, to permit the movement experienced when the bathtub remains in usage. The sealer can split relatively early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the market. It is recommended to fit the tiles using water-resistant or water resistant sticky as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I am very curious about Tools You Need to Install a New Bathtub and I really hope you appreciated my blog posting. Loved our posting? Please share it. Help another person find it. Bless you for your time. Kindly come visit our blog back soon.

Quick fix? Dial now.